Fuel level sender for fuel tank

 Sorry, this part is no longer available.

01103030

Replacement regulator rectifier for models fitted with the Ducati charging system. This is a quality unit and is supplied with fitting instructions

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black ring, 1 x red ring. You will need to reuse your existing block connectors to connect this to your loom. See this wiring diagram for wiring connections

 This part is due back in stock soon, call 01484 841395 to reserve yours

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

Fuel level sender for fuel tank

2 pin connector block. Use seal TAA90103 with this part

 This part is due back in stock soon, call 01484 841395 to reserve yours

29103050-z 29103050 GU29103050 29 10 30 50
 2910 3050 2910.3050 29.10.30.50

Fuel level sender for fuel tank

2 pin connector block

 This part is available by special order, request a quote

 30103000 GU30103000 30 10 30 00
 3010 3000 3010.3000 30.10.30.00

Speedo sensor with 100cm lead and 3 pin plug for non ABS equipped models

 This part is available by special order, request a quote

AP8124985

Pair of low and high chrome Voxbell Fiamm type snail horns. Very loud and Italian!

Chromed plastic grill and cover, also known as Guzzi ref. 28743761. Sold with brackets, can be fitted to most Guzzis

 This part is available by special order, request a quote

28743760-z 28743760 GU28743760 28 74 37 60
 2874 3760 2874.3760 28.74.37.60

Factory heated grip kit to keep your hands toastie warm all year round. Three heat levels, integrates with the V85 TT wiring and TFT dashboard. The grips are switched on by a button on the left hand switchgear. Fully compatible with fly by wire (unlike aftermarket grips).

Includes a complete heated twistgrip, heated grip for the clutch side and fitting instructions. The thottle has to be calibrated at an official Moto Guzzi dealer with the factory software after installation.

 This part is available by special order, request a quote

2S001325

Speedo sensor on ABS equipped models, used for front and rear applications depending on model

Used as rear wheel ABS sensor on V85TT, front and rear sensor on V7 II ABS equipped models. There are several variants of these sensors, please compare to the sensor on your bike or contact us with a chassis number before ordering. Supercedes Guzzi ref. 6429875. 2 pin connector

 This part is due back in stock soon, call 01484 841395 to reserve yours

 859792 MG859792

Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders.

• Outputs 600W @5000 RPM
• Supplied with rotor removal tool
• For tapered crankshafts

1. Remove stator and rotor using the supplied rotor removal tool
2. Remove the old stator windings from the stator plate
3. Solder in the new stator widing wires to the connection block on the stator plate and reconnect the
4. Mount the replacement diode board, this should be protected from the weather but cooled by passing air
5. Connect up the system as follows: Terminals U,V and W take the three yellow wires which should be connected to the stator plate block; Y goes to Y on the stator plate; The brown wires go to earth (we recommend using some earth sleeve on these if possible); Red goes to the battery positive terminal; regulator wiring remains as before (D+ to diode board, D- to earth and DF to brush holder)
6. Check charge warning light is working (earth DF wire at stator to check bulb function)
7. Turn motor over by hand to ensure everything is seated correctly, there should be an air gap between the stator windings amd rotor
Fit alternator cover and spacer

 This part is available by special order, request a quote

Brakelight switch banjo bolt

See BRA01004 and BRA01014 for alternative universal stop light switch. Also known as Guzzi ref. 06261020, 000037891, 800037891, 079654114, 14657050

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14657959 GU14657959 14 65 79 59
 1465 7959 1465.7959 14.65.79.59